- #INSTALLING WINCH ON POLARIS SPORTSMAN 450 INSTALL#
- #INSTALLING WINCH ON POLARIS SPORTSMAN 450 MANUAL#
- #INSTALLING WINCH ON POLARIS SPORTSMAN 450 FREE#
Check and confirm wire routing and connections are as shown and make necessary adjustment before moving to next installation steps.
#INSTALLING WINCH ON POLARIS SPORTSMAN 450 MANUAL#
NOTE: See the Electrical Connections Reference Guide section of the instruction manual for detailed photos of each part and their respective connections.ġ1. NOTE: Before installing the winch kit, add or replace the proper fluid to your front gearcase as required per your vehicles service manual as this process will be difficult to do after the winch is installed. If you do not plan to use a plow on your vehicle, cut out the center section as shown and reinstall winch cover on the lower front bumper cover if you desire, but it is not required. If you plan to use a plow, remove winch cover from the lower front bumper cover and do not reinstall. Remove winch cover from the lower front bumper cover. Retain bolts for use during reinstallation. Remove lower front bumper cover from vehicle by removing four bolts as shown. SPORTSMAN 450/570 PREPARATION (continued):ĩ. Remove the accessory front brush guard from vehicle (if equipped). Disconnect the black (negative) and red (positive) cables from the busbar as shown. Failure to do so will result in high current electrical arc, and may result in battery explosion if tool touches grounded frame. Disconnect black (negative) and red (positive) cables from battery.ĪLWAYS disconnect black negative (-) cable from battery FIRST. Lift the front cover upwards slowly to disengage the tabs on cover from the slots as shown. Remove four screws holding front cover in place as shown. Open the front rack and remove rubber seal as shown. Detach the rubber latch on both sides to open front rack as shown. Turn key to "OFF" position and remove from vehicle.Ģ. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.ġ.
#INSTALLING WINCH ON POLARIS SPORTSMAN 450 FREE#
Installation is easier if the vehicle is clean and free of debris. Installation instructions thoroughly before beginning. Important: Your Kolpin Sportsman Quick-Mount Winch Kit is exclusively designed for your vehicle.
Then follow the preceding instructions for final installation. The XP instructions shows the contactor location and wire routing for that configuration, and reassemble the contactor and wiring to match those photos.
#INSTALLING WINCH ON POLARIS SPORTSMAN 450 INSTALL#
Sportsman XP Note: If you need to install this kit on a Sportsman XP 550/850/1000, see the instructions and photos Service Free Spool Handle Knob (not included in kit) Hex Flange Locknut, Zinc Plated, M8 x 1.25 Rubber Winch Stopper (only included on 3500lb.)īutton Screw, Zinc Plated, M8 x 1.25 - 20mm LGġ6 2 Socket Head Cap Screw, Zinc Plated, M6 x 1.0 - 10mm LGĬarriage Screw, Zinc Plated, M8 x 1.25 - 20mm LG Power Connection Cable, Black 6 GA (510mm) Winch Connection Cable, Blue 6 GA (267mm) Winch Connection Cable, Yellow 6 GA (368mm) Hex Flange Screw, Zinc Plated, M8 x 1.25 - 25mm LG Mounting Bracket Note: If any hardware is missing, do not return to the store. These installation instructions for future reference and parts ordering information. Before You Begin: Read these instructions and check to be sure all parts and tools are accounted for. Product Instructions | Part No: 26-3100 / 26-3110Īpplication: Polaris Sportsman, verify accessory fitment at. File Info : application/pdf, 15 Pages, 1.92MB Document Document 26-3100 kolpin english ?v=828c8287 Polaris Sportsman Quick-Mount 2500lb.
0 kommentar(er)
